表面再结晶对定向凝固高温合金高周疲劳行为的影响

采用悬臂旋转弯曲试验,研究定向凝固DZ4合金在喷丸预变形及热处理后产生的再结晶层对高周疲劳寿命的影响.结果表明,DZ4合金经过一定程度的预变形,在随后的高温热处理后表面会产生一定厚度的再结晶;再结晶层对DZ4合金高周疲劳寿命有一定影响;在一定喷丸强度范围内,随喷丸强度增加,疲劳寿命先减小后增大.     

大迎角下鸭翼涡与边条涡的干扰特性

 在风洞测力、水洞染色线和激光片光实验的基础上 ,对翼身组合体鸭翼边条翼布局大迎角涡系干扰机理进行了分析和探讨 ,揭示了该布局增升的机理。鸭翼涡位于机翼内侧 ,其与边条涡的相互诱导致使边条涡向外翼偏折 ,既改善了外翼的流态 ,又使机翼前缘涡量卷入边条涡 ,增强了边条涡的强度 ,从而延迟其破裂。两方面的共同作用 ,提高了主翼的涡升力 ,起到增升作用。     

飞机载荷/环境谱编制研究及应用

阐明了编制恰当的载荷/环境谱是飞机结构疲劳、损伤容限和耐久性设计或现有机种寿命评定中的首要工作,它对后续的分析和试验工作的成败、经费、工作量和时间都有重大的影响。介绍了根据不同的工作任务和技术要求,有多种形式的载荷/环境谱及相应的编谱方法,主要对载荷/环境谱的编制技术进行了研究,提出了具有指导意义的一般性方法,最后给出了某型飞机的载荷环境谱。     

F-16飞机大迎角飞行偏离/尾旋特性分析

通过俯仰力矩系数随迎角的变化对F－16飞机的气动特性进行分析，并对其中大迎角时的偏离特性进行了剖析，通过计算给出了F－16飞机的m^βx,m^βy,m^δy,m^δyx,m^δyy,m^δyxy以及侧滑偏离参数（m^βydyn)和横向操纵偏离参数（LCDP）随迎角的变化曲线，最后通过m^βydyn和LCDP的综合，预测了F－16飞机的偏离特性，同时通过计算对尾旋运动特性和改出特性进行了研究，为分析F－16飞机大迎角飞行特性提供了理论依据。     

内爆炸圆管破片初速研究

分析内爆炸圆管膨胀破碎过程的应力,提出确定内爆炸圆管断裂半径的复合判据,从理论上预测不同材料圆管的破片初速度.采用GSJ高速摄影记录仪测试不同材料圆管的破片初速度,并与理论预测值行比较.结果表明,采用复合判据得到的理论预测结果与实验测量结果能够较好吻合.     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

热处理对二次锻造高Nb-TiAl基合金组织的影响

研究了热处理对二次锻造高Nb-TiAl基合金组织的影响。通过对Ti-45Al-9(Nb,W,B,Y)金属间化合物进行不同的热处理,得到不同的显微组织。结果表明,经1310℃/20min+1250℃/2h/AC热处理后,β相被有效地消除,得到细小均匀的双态组织。此后直接加热到α单相区,得到条带状的全片层组织。增加在两相区的停留,得到相对比较均匀细小的全片层组织。将锻造组织先转变为近γ组织再进行全片层组织处理,得到最均匀细小的全片层组织。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

大攻角流动的非定常特性分析

本文首先通过动态测量手段研究了大攻角流场中的能量成分,分析了各种成分引发的非定常性对大攻角流动的影响。结果表明大攻角流动本身是一种“涡行为”,非定常性对大攻角流动非对称性的影响较弱,影响大攻角流动的本质因素是涡的动力不稳定性对于前体不确定小扰动的响应。     

Study on the breakup lengths of free round liquid jets

IntroductionBreakup and atomization of roundliquidjetshad been widely used in internal combustion en-gines,gas turbines,and liquid rocket engines.Recently,with the development of scramjet en-gines and the deepening of fuel atomization re-search,it attract…